table tennis rubbers consist of a top sheet (the outer surface) and a sponge (the part attached to the blade, although some tires as only the top sheet can be used. Although most players buy a tire with two already glued together, some players are much more common in pickling players to their top-sheet and sponge to make combinations, and therefore need a good way to glue together.
Pasting a top-sheet with a sponge is a bit 'more complicatedStick a tire with a knife, but it is not difficult, since it is expected that bought it as a rubber, if you look like. Once you cut the blade and you will see that they can no longer be able to difference.
For bonding a face sheet with a sponge, you need a good glue or mastic, but more often are generally better because they have more in their adhesives. I usually use putty in a store of art, which tends more often with the many table tennis.
You need to put glueboth on the top sheet and sponge for good adhesion. The most important thing to remember is to be patient with each step ... There is no need to run all these steps, so take your time ...
1. Place a layer of glue on the sponge. Now, depending on the sponge or glue, this can make it expand a bit '. It 'important to reduce it to its normal size before applying the top sheet. If you do not withdraw and leave after applying the cover, the cover at the end of compression,The slower and less sensitive. You can usually tell which is growing because some arches or domes'. As a general rule, within half an hour or less flat. If the sponge is a bit 'bent forward, you may want to stick to hard surface with a thin layer of glue, and prevent stretching.
2 (a). To invert a flat tire you have to paste on Easy on the tip of the prongs. It 's important not to get stuck between the souls that could so that they trickle down to the topSurface, causing it to expand it (bubble up) and could affect the playing surface. The way I make my brush a layer of glue on a flat surface that absorbs the glue, such as glass, a table or many plastics. Then I just remove the top sheet with tips down to the layer of glue, and slide around a bit 'in any part of the paper, then. Verify that the core so that all seeds coated with glue, otherwise you must repeat the procedure. Youmust take great care to ensure that the rubber tip on itself as it can be difficult to return it to pull apart.
2 (b). Rubber molded (pips short, medium or long), you must obtain a layer of glue over the surface. Put it on a flat surface, half down and brush a layer of glue in there. It pays to put some 'small weights on the corners of the rubber, because the base sheet of thin rubber seeds extended slightly so that it shrinks very easily. Need to be carefulMake sure the rubber tip on itself as it can be difficult to return it to pull apart. It will shrink a bit 'so you have to wait until it is directed quite a bit' out again. This usually takes 10 to 20 minutes. You can still seem a bit 'wobbly, but this is not a big problem.
3 (a). Hold for inverted, with their hands over the sheet edges, align with the bottom of the sponge, and just put it there. Do not try to stretch the rubber, while holding, theThis set of a pair of uneven tension on the first page. If you want a certain tension in the top-sheet, you can restore with a heavy roller or a bottle, and stretch them a little 'while they are together. This takes a little 'practice, I would not recommend it if it's the first time is when you stick a card top of a sponge. Try to stretch, not too much, a little 'tension is already very effective.
3 (b). Pips for this is a bit 'difficult, since the package more flexible. HoldingThey folded their hands over the standard allows (not glued or folded pages never glued together). Align the top sheet at the bottom of the sponge, and whose land the 10mm or so. Then use a roller to gently roll the rest of the sponge pips plate. This is important because you do not want bubbles under the top sheet. Try not to stress the upper plate, as you pull them.
4. Put some weight on the rubber top sheet, press theSponge. For pimpled rubber, press the bottom of the sheet (part of the label) hard on the fingers, can not be pushed down the books.
Especially for tire flip, it is important not to put much weight on the rubber, in order to push the seeds into the sponge and the edges of the core could join in the towel, perhaps producing an uneven surface and inconsistent.
5. I like to keep all night, but should be finished after an hour orSun You can check to see how you try to work the corners of the pan. It should be pretty well locked, perhaps a little 'relaxed, where he was holding when you put the top sheet onto the sponge, but that part is not used when cutting, so it should not matter. I used this method many times, and also the rubber glued several times after the speed, and has not loosened. Creating too much but could weaken with the velocity.
We hope that this guide is for you,and you can start your own top-sheet a sponge trying to combinations!
